Search:  
Gentoo Wiki

Clevo_D900K/Boot_Messages

Back to main page

This is the full dmesg output using the given kernel .config:

Bootdata ok (command line is root=/dev/md1 vga=0x318 video=vesafb:mtrr,1024x768-32)
Linux version 2.6.15-gentoo-r7-v2 (root@odysseus) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #2 SMP PREEMPT Wed Mar 8 01:10:01 CST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
 BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000c2000 - 00000000000d0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ff00000 (usable)
 BIOS-e820: 000000007ff00000 - 000000007ff13000 (ACPI data)
 BIOS-e820: 000000007ff13000 - 000000007ff80000 (ACPI NVS)
 BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 PTLTD                                 ) @ 0x00000000000f7220
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x000000007ff0e6cd
ACPI: FADT (v001 CLEVO  PTLTW    0x06040000 PTL_ 0x000f4240) @ 0x000000007ff12da0
ACPI: SSDT (v001 PTLTD  POWERNOW 0x06040000  LTP 0x00000001) @ 0x000000007ff12e14
ACPI: MADT (v001 PTLTD  	 APIC   0x06040000  LTP 0x00000000) @ 0x000000007ff12f5a
ACPI: MCFG (v001 PTLTD    MCFG   0x06040000  LTP 0x00000000) @ 0x000000007ff12fc4
ACPI: DSDT (v001  CLEVO PTL_ACPI 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 515590
  DMA zone: 2762 pages, LIFO batch:0
  DMA32 zone: 512828 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfecc0000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 3, address 0xfecc0000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ10 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
Built 1 zonelists
Kernel command line: root=/dev/md1 vga=0x318 video=vesafb:mtrr,1024x768-32
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2600.178 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 2059024k/2096128k available (2836k kernel code, 36688k reserved, 1306k data, 204k init)
Calibrating delay using timer specific routine.. 5209.93 BogoMIPS (lpj=2604965)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5199.42 BogoMIPS (lpj=2599714)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
AMD Athlon(tm) 64 FX-60 Dual Core Processor  stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 688 cycles)
Brought up 2 CPUs
Disabling vsyscall due to use of PM timer
time.c: Using PM based timekeeping.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
PCI: Using MMCONFIG at e0000000
ACPI: Subsystem revision 20050902
    ACPI-0339: *** Error: Looking up [\_SB_.PCI0.PIB_.LNKH] in namespace, AE_NOT_FOUND
search_node ffff810002f87d80 start_node ffff810002f87d80 return_node 0000000000000000
    ACPI-0339: *** Error: Looking up [\_SB_.PCI0.LNKH] in namespace, AE_NOT_FOUND
search_node ffff810002f92ec0 start_node ffff810002f92ec0 return_node 0000000000000000
    ACPI-0339: *** Error: Looking up [\_SB_.PCI0.LNKH] in namespace, AE_NOT_FOUND
search_node ffff810002f92640 start_node ffff810002f92640 return_node 0000000000000000
    ACPI-0339: *** Error: Looking up [\_SB_.PCI0.LNKH] in namespace, AE_NOT_FOUND
search_node ffff810002f92380 start_node ffff810002f92380 return_node 0000000000000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *11, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *11, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *11, disabled.
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: Embedded Controller [EC] (gpe 11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE0C._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2C._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 23
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:05: ioport range 0xfe00-0xfe00 has been reserved
pnp: 00:05: ioport range 0x4000-0x407f could not be reserved
pnp: 00:05: ioport range 0x4100-0x411f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:02:00.0
PCI: Bridge: 0000:00:02.0
  IO window: 5000-5fff
  MEM window: d0000000-d1ffffff
  PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.2
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bus 5, cardbus bridge: 0000:00:05.0
  IO window: 00002400-000024ff
  IO window: 00002800-000028ff
  PREFETCH window: 88000000-89ffffff
  MEM window: 8a000000-8bffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 16
PCI: Via IRQ fixup for 0000:00:02.0, from 9 to 0
PCI: Setting latency timer of device 0000:00:02.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:03.0, from 9 to 1
PCI: Setting latency timer of device 0000:00:03.0 to 64
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 31 (level, low) -> IRQ 17
PCI: Via IRQ fixup for 0000:00:03.2, from 9 to 1
PCI: Setting latency timer of device 0000:00:03.2 to 64
PCI: Enabling device 0000:00:05.0 (0000 -> 0003)
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 18 (level, low) -> IRQ 18
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
PCI: Bypassing VIA 8237 APIC De-Assert Message
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie01]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie01]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 31 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:03.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie01]
Allocate Port Service[pcie03]
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xb0000000
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20010200000, using 6144k, total 262144k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
vesafb: Mode is not VGA compatible
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (CM) [PWRB]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Video Device [NVD] (multi-head: yes  rom: no  post: no)
Using specific hotkey driver
ACPI: Thermal Zone [THM0] (51 C)
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
loop: loaded (max 8 devices)
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xffffc20000014800, 00:90:f5:4c:9a:2a, IRQ 19
usbcore: registered new driver irda-usb
USB IrDA support registered
usbcore: registered new driver stir4200
nsc-ircc, Found chip at base=0x02e
nsc-ircc, Wrong chip version ff
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:0f.1, from 0 to 4
Losing some ticks... checking if CPU frequency changed.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
input: AT Translated Set 2 keyboard as /class/input/input1
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0x2090-0x2097, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x2098-0x209f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
Synaptics Touchpad, model: 1, fw: 5.9, id: 0xa36eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input2
hdc: PIONEER DVD-RW DVR-K16, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
PCI: Via IRQ fixup for 0000:00:0f.0, from 11 to 4
sata_via 0000:00:0f.0: routed to hard irq line 4
ata1: SATA max UDMA/133 cmd 0x20B0 ctl 0x20A6 bmdma 0x2080 irq 20
ata2: SATA max UDMA/133 cmd 0x20A8 ctl 0x20A2 bmdma 0x2088 irq 20
ata1: dev 0 cfg 49:0f00 82:746b 83:7f69 84:4063 85:7469 86:3d49 87:4063 88:203f
ata1: dev 0 ATA-7, max UDMA/100, 195371568 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_via
ata2: dev 0 cfg 49:0f00 82:746b 83:7f69 84:4063 85:7469 86:3d49 87:4063 88:203f
ata2: dev 0 ATA-7, max UDMA/100, 195371568 sectors: LBA48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_via
  Vendor: ATA       Model: HTS721010G9SA00   Rev: MCZO
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: HTS721010G9SA00   Rev: MCZO
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 195371568 512-byte hdwr sectors (100030 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 195371568 512-byte hdwr sectors (100030 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb4
sd 1:0:0:0: Attached scsi disk sdb
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d2206000-d22067ff]  Max Packet=[2048]
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 18 (level, low) -> IRQ 18
Yenta: CardBus bridge found at 0000:00:05.0 [1558:0901]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:05.0, mfunc 0x00001002, devctl 0x64
Yenta: ISA IRQ mask 0x0a38, PCI irq 18
Socket status: 30000006
ACPI: PCI Interrupt Link [ALKD] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 21
GSI 21 sharing vector 0xD1 and IRQ 21
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.4, from 11 to 5
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 21, io mem 0xd2206c00
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 21, io base 0x00002000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x00002020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 5
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x00002040
usb 1-2: new high speed USB device using ehci_hcd and address 3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0090f500004c9a2a]
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 5
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 21, io base 0x00002060
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
i2c /dev entries driver
usb 1-4: new high speed USB device using ehci_hcd and address 4
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC).
via82xx: Assuming DXS channels with 48k fixed sample rate.
         Please try dxs_support=5 option
         and report if it works on your machine.
         For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt Link [ALKC] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
GSI 22 sharing vector 0xD9 and IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22
PCI: Via IRQ fixup for 0000:00:11.5, from 11 to 6
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 2-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22
PCI: Via IRQ fixup for 0000:00:11.6, from 11 to 6
PCI: Setting latency timer of device 0000:00:11.6 to 64
MC'97 1 converters and GPIO not ready (0xff00)
ALSA device list:
  #0: VIA 8237 with ALC850 at 0x1800, irq 22
  #1: VIA 82XX modem at 0x1c00, irq 22
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8:    0 : fid 0x12 (2600 MHz), vid 0xa (1300 mV)
powernow-k8:    1 : fid 0x4 (1200 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0x2, vid 0x12
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb4 ...
md:  adding sdb4 ...
md: sdb1 has different UUID to sdb4
md:  adding sda4 ...
md: sda1 has different UUID to sdb4
md: created md1
md: bind<sda4>
md: bind<sdb4>
md: running: <sdb4><sda4>
md1: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb4
raid0:   comparing sdb4(48853568) with sdb4(48853568)
raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at sda4
raid0:   comparing sda4(48853568) with sdb4(48853568)
raid0:   EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 97707136 blocks.
raid0 : conf->hash_spacing is 97707136 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: considering sdb1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: md1: found reiserfs format "3.6" with standard journal
ReiserFS: md1: using ordered data mode
ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md1: checking transaction log (md1)
ReiserFS: md1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
eth1394: $Rev: 1312 $ Ben Collins <bcollins@debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
nvidia: module license 'NVIDIA' taints kernel.
GSI 23 sharing vector 0xE1 and IRQ 23
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 24 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:02:00.0 to 64
NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module  1.0-8178  Wed Dec 14 16:58:07 PST 2005
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
input: Kensington Kensington PocketMouse Pro as /class/input/input3
input: USB HID v1.00 Mouse [Kensington Kensington PocketMouse Pro] on usb-0000:00:10.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
  Vendor: GENERIC   Model: USB Storage-CFC   Rev: 019A
  Type:   Direct-Access                      ANSI SCSI revision: 00
sd 2:0:0:0: Attached scsi removable disk sdc
usb-storage: device scan complete
usb 2-1: USB disconnect, address 2
usb 2-1: new low speed USB device using uhci_hcd and address 3
input: Kensington Kensington PocketMouse Pro as /class/input/input4
input: USB HID v1.00 Mouse [Kensington Kensington PocketMouse Pro] on usb-0000:00:10.0-1
r8169: eth0: link up
r8169: eth0: link up
Retrieved from "http://www.gentoo-wiki.info/Clevo_D900K/Boot_Messages"

Last modified: Wed, 15 Oct 2008 00:23:00 +0000 Hits: 3,419