Search:  
Gentoo Wiki

Acer_Aspire_4315/Boot_Messages

Return to main page

This is the full dmesg output using the given kernel .config:

Linux version 2.6.23-gentoo-r8 (root@Larry) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #2 SMP Fri Feb 29 08:43:10 CST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003f6d0000 (usable)
 BIOS-e820: 000000003f6d0000 - 000000003f6e0000 (ACPI NVS)
 BIOS-e820: 000000003f6e0000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
118MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7e10
Entering add_active_range(0, 0, 259792) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   259792
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   259792
On node 0 totalpages: 259792
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 237 pages used for memmap
  HighMem zone: 30179 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
DMI present.
Using APIC driver default
ACPI: RSDP 000F7CA0, 0024 (r2 PTLTD )
ACPI: XSDT 3F6D2FEF, 008C (r1 ACRSYS ACRPRDCT  6040000 INNA        0)
ACPI: FACP 3F6DCC48, 00F4 (r3 INTEL  CRESTLNE  6040000 ALAN        1)
ACPI: DSDT 3F6D4147, 8A8D (r2 INTEL  CRESTLNE  6040000 MSFT  3000000)
ACPI: FACS 3F6DFFC0, 0040
ACPI: HPET 3F6DCD3C, 0038 (r1 INTEL  CRESTLNE  6040000 LOHR       5A)
ACPI: MCFG 3F6DCD74, 003C (r1 INTEL  CRESTLNE  6040000 LOHR       5A)
ACPI: TCPA 3F6DCDB0, 0032 (r1 Intel   CRESTLN  6040000          5A52)
ACPI: TMOR 3F6DCDE2, 0026 (r1 PTLTD            6040000 PTL         3)
ACPI: SLIC 3F6DCE08, 0176 (r1 ACRSYS ACRPRDCT  6040000 ANNI        1)
ACPI: APIC 3F6DCF7E, 005A (r1 PTLTD  	 APIC    6040000  LTP        0)
ACPI: BOOT 3F6DCFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SSDT 3F6D3E6A, 02DD (r1 SataRe SataAhci     1000 INTL 20050624)
ACPI: SSDT 3F6D3C9F, 01CB (r1 BrtRef  DD01BRT     1000 INTL 20050624)
ACPI: SSDT 3F6D37C0, 04DF (r1  PmRef  Cpu0Cst     3001 INTL 20050624)
ACPI: SSDT 3F6D3561, 025F (r1  PmRef  Cpu0Tst     3000 INTL 20050624)
ACPI: SSDT 3F6D307B, 04E6 (r1  PmRef    CpuPm     3000 INTL 20050624)
ACPI: DMI detected: Acer
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 7:6 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order.  Total pages: 257763
Kernel command line: root=/dev/sda7
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1862.255 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1022804k/1039168k available (3755k kernel code, 15724k reserved, 1878k data, 276k init, 121664k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff9a000 - 0xfffff000   ( 404 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc068a000 - 0xc06cf000   ( 276 kB)
      .data : 0xc04aaca1 - 0xc06805ec   (1878 kB)
      .text : 0xc0100000 - 0xc04aaca1   (3755 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Calibrating delay using timer specific routine.. 3728.31 BogoMIPS (lpj=7456625)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afebfbff 20100000 00000000 00000000 0000e31d 00000000 00000001 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afebfbff 20100000 00000000 00003940 0000e31d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 20k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1073 Objects with 79 Devices 266 Methods 34 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 15 Objects with 3 Devices 9 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0003) - 3 Objects with 0 Devices 3 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0004) - 2 Objects with 0 Devices 1 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0005) - 7 Objects with 0 Devices 3 Methods 0 Regions
Parsing all Control Methods:
Table [SSDT](id 0006) - 13 Objects with 0 Devices 4 Methods 0 Regions
 tbxface-0598 [00] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
CPU0: Intel(R) Celeron(R) CPU          540  @ 1.86GHz stepping 01
Total of 1 processors activated (3728.31 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 6 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
Completing Region/Field/Buffer/Package initialization:.......................................................................................
Initialized 30/34 Regions 11/11 Fields 33/34 Buffers 13/21 Packages (1122 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:<5>ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: If "acpi_osi=Linux" works better, please notify linux-acpi@vger.kernel.org
.
Executed 1 _INI methods requiring 0 _STA executions (examined 88 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Time: tsc clocksource has been installed.
pnp: 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
pnp: 00:06: iomem range 0xfed00000-0xfed003ff could not be reserved
pnp: 00:08: iomem range 0xff800000-0xff800fff could not be reserved
PCI: Bridge: 0000:00:1c.0
  IO window: 2000-2fff
  MEM window: f6000000-f7ffffff
  PREFETCH window: f0000000-f1ffffff
PCI: Bridge: 0000:00:1c.1
  IO window: 3000-3fff
  MEM window: f8000000-f9ffffff
  PREFETCH window: f2000000-f3ffffff
PCI: Bridge: 0000:00:1c.2
  IO window: 4000-4fff
  MEM window: fa000000-fbffffff
  PREFETCH window: f4000000-f5ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:00:02.0
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.102
agpgart: Detected an Intel 965GM Chipset.
agpgart: Detected 7676K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID0]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI Exception (processor_core-0821): AE_NOT_FOUND, Processor Device is not present [20070126]
Marking TSC unstable due to: possible TSC halt in C2.
Time: hpet clocksource has been installed.
Switched to high resolution mode on CPU 0
ACPI: Thermal Zone [TZS0] (49 C)
ACPI: Thermal Zone [TZS1] (48 C)
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Clocksource tsc unstable (delta = -499999805 ns)
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
sky2 0000:02:00.0: v1.18 addr 0xf6000000 irq 16 Yukon-FE (0xb7) rev 3
sky2 eth0: addr 00:1d:72:0e:5b:e4
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH8M: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ 19
ICH8M: chipset revision 3
ICH8M: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: TSSTcorpCDW/DVD TS-L462D, ATAPI CD/DVD-ROM drive
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
ahci 0000:00:1f.2: version 2.3
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part 
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 cmd 0xf883e100 ctl 0x00000000 bmdma 0x00000000 irq 222
ata2: SATA max UDMA/133 cmd 0xf883e180 ctl 0x00000000 bmdma 0x00000000 irq 222
ata3: SATA max UDMA/133 cmd 0xf883e200 ctl 0x00000000 bmdma 0x00000000 irq 222
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: Hitachi HTS542512K9SA00, BB2OC31P, max UDMA/133
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54251 BB2O PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
Fusion MPT base driver 3.04.05
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.05
ieee1394: raw1394: /dev/raw1394 device initialized
kvm: no hardware support
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 20, io mem 0xfc404800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xfc404c00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 22, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 21, io base 0x00001860
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00001880
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input3
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Fri Jul 20 09:12:58 2007 UTC).
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
ALSA device list:
  #0: HDA Intel at 0xfc200000 irq 23
oprofile: using timer interrupt.
pktgen v2.68: Packet Generator for packet performance testing.
TCP probe registered (port=0)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
Using IPI No-Shortcut mode
Synaptics Touchpad, model: 1, fw: 6.5, id: 0x81a0b1, caps: 0xa04711/0xa04000
input: SynPS/2 Synaptics TouchPad as /class/input/input4
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 276k freed
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.10.2.2-ATHEROS (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425)
wlan: 0.8.4.2 (svn r2756)
ath_pci: 0.9.4.5 (svn r2756)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:04:00.0 to 64
ath_pci: switching rfkill capability off
ath_rate_sample: 1.2 (svn r2756)
ath_pci: switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 14.2 phy 7.0 radio 10.2
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5424/2424: mem=0xf8000000, irq=17
EXT3 FS on sda7, internal journal
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Successfully loaded version 1.5.4 (interface 0x00050002).
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 522104k swap on /dev/sda5.  Priority:-1 extents:1 across:522104k
soundcore: exports duplicate symbol sound_class (owned by kernel)
snd: exports duplicate symbol snd_major (owned by kernel)
snd_mixer_oss: exports duplicate symbol snd_mixer_oss_ioctl_card (owned by kernel)
snd_page_alloc: exports duplicate symbol snd_dma_alloc_pages (owned by kernel)
snd_timer: exports duplicate symbol snd_timer_open (owned by kernel)
snd_pcm: exports duplicate symbol snd_pcm_new_stream (owned by kernel)
kobject_add failed for snd_pcm_oss with -EEXIST, don't try to register things with the same name in the same directory.
 [<c0240e4e>] kobject_shadow_add+0x155/0x187
 [<c013dce7>] mod_sysfs_setup+0x18/0x8b
 [<c013f00a>] sys_init_module+0x1139/0x148b
 [<c03ead9e>] snd_pcm_format_width+0x0/0x1c
 [<c0164b1f>] sys_read+0x41/0x67
 [<c0104daa>] sysenter_past_esp+0x5f/0x85
 =======================
soundcore: exports duplicate symbol sound_class (owned by kernel)
snd: exports duplicate symbol snd_major (owned by kernel)
snd_mixer_oss: exports duplicate symbol snd_mixer_oss_ioctl_card (owned by kernel)
soundcore: exports duplicate symbol sound_class (owned by kernel)
snd: exports duplicate symbol snd_major (owned by kernel)
snd_seq_device: exports duplicate symbol snd_seq_device_load_drivers (owned by kernel)
snd_timer: exports duplicate symbol snd_timer_open (owned by kernel)
snd_seq: exports duplicate symbol snd_use_lock_sync_helper (owned by kernel)
snd_seq_midi_event: exports duplicate symbol snd_midi_event_new (owned by kernel)
kobject_add failed for snd_seq_oss with -EEXIST, don't try to register things with the same name in the same directory.
 [<c0240e4e>] kobject_shadow_add+0x155/0x187
 [<c013dce7>] mod_sysfs_setup+0x18/0x8b
 [<c013f00a>] sys_init_module+0x1139/0x148b
 [<c0164b1f>] sys_read+0x41/0x67
 [<c0104daa>] sysenter_past_esp+0x5f/0x85
 [<c04a0000>] ieee80211_parse_info_param+0x42/0x63c
 =======================
soundcore: exports duplicate symbol sound_class (owned by kernel)
snd: exports duplicate symbol snd_major (owned by kernel)
snd_seq_device: exports duplicate symbol snd_seq_device_load_drivers (owned by kernel)
snd_timer: exports duplicate symbol snd_timer_open (owned by kernel)
snd_seq: exports duplicate symbol snd_use_lock_sync_helper (owned by kernel)
ath0: no IPv6 routers present

Retrieved from "http://www.gentoo-wiki.info/Acer_Aspire_4315/Boot_Messages"

Last modified: Thu, 14 Aug 2008 02:18:00 +0000 Hits: 1,077