Search:  
Gentoo Wiki

MSI_Megabook_m655

Contents

Introduction

The MSI 1039 is a 64 bit AMD laptop made by MSI that will run linux but is difficult to set up, mostly during installation. Due to the similarities between the MSI 1039, MSI 1036, and MSI 1029; some things that work for one will work for the other. One can use this as a start for the MSI 1036 which currently lacks a wiki, or one could use tricks that work on the MSI 1029 on the MSI 1039 and have a reasonable chance of success. As there are some people who will read this but are not installing Gentoo (everyone who uses linux occassionally has to read documentation or instructions geared for another distrobution), there will be some instructions like emerge some-package. For those not using Gentoo, that is the Gentoo way of installing some-package. Just use whatever is the package utility or a tarball for your distro.

64 bit Gentoo

This wiki is geared towards running x86_64 Gentoo on this laptop. As such, assume that everything is for a 64 bit OS unless it says otherwise.

32 bit Gentoo

32 bit Gentoo (x86) hasn't been tested yet. Most likely, the same thing can be done as with the 64 bit Gentoo.

Hardware Overview

Green means that it works without having to do anything specific to this laptop. Blue means that it works but special things need to be done that are specific to this laptop. Purple means that it works but some features haven't been tested yet. Yellow means that it partially works. Red means that it doesn't work. Gray means that it is unknown whether it works or not.

Hardware CategoryModel/TypeWorks or Not
CPUAMD Turion up to 2.2GHzWorks correctly including PowerNow
MemoryDDR333/DDR400Works correctly
ScreenUp to 1280x800Works correctly
USB4 portsAll work correctly
TouchpadElantek TouchpadWorks but disabling tap clicking isn't tested
CD/DVD DriveCD-RW/DVD-RW/DVD+RWWorks but burning DVD's doesn't work in TAO mode
Video CardATI X1600 PCIEWorks but is difficult to set up
Network CardRealtek 8168 PCIEWorks but setting up the driver is problematic
SoundATI SB450 HDA AudioWorks but the microphone hasn't been tested
WirelessRaLink RT2500Works
PCMCIAPCMCIA I/IIUnknown but appears to be Yenta compatable?
BluetoothUSB BluetoothUnknown
Builtin CameraMicrodia USB CameraUnknown
Multicard ReaderO2 Micro OZ711MP1/MS1 Memory Card BusUnknown
Firewire1 O2 Micro IEEE1394 miniportUnknown
Multimedia Keysbrightness/volume/wireless/etcBrightness and wireless ones work; others: unknown

Installing Gentoo

Installation is tricky since the network card isn't natively supported in the kernel and booting the laptop with a CD can hang.

Preparing for Installation

The driver for the network card needs to be obtained from the company's website http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false#2. This driver named r1000.tar.gz. Since this driver is needed for installation it needs to be put somewhere that linux can get to without a network connection such as another partition on the hard drive, appended as another session to the Gentoo Installation CD, on a USB floppy drive, etc. For more information, read RTL8168. Since there will be no network connection until after reboot; the stage3 tarball, portage snapshot, and distfiles on the installation CD will have to be used. It is thus advisable to use the Gentoo LiveCD since it has everything.

Booting from CD

If the laptop is allowed to boot with the installation CD in the drive, it will hang if left to its own when it starts udev regardless of kernel options. The reason for this is unknown. When booting, remove the battery and leave the laptop on AC power. That way, if it hangs, pull the power. The trick is to hit Ctrl+Alt+Delete right before udev starts. If the gentoo kernel with frambuffers is used, the screen will be blank and then a lot of lines of text will be printed until the lines of text are about midway down the screen where udev is initialized. Hit Ctrl+Alt+Delete when the text is halfway down the screen. If you press too late, the computer will hang and you will have to cut the power and start over again. This will reboot the computer. This time, let it boot normally without hitting Ctrl+Alt+Delete. Udev initialization won't hang this time for an unknown reason and the system will reach the login without hanging.

Kernel Config

Below it the kernel configuration that will make the laptop work with the working features on the chart. However, additional configuration may be necessary to get the remaining hardware working and some of the configuration information may not be needed. Other generic items such as changing the frequency of the CPU are not listed because they are not specific to this laptop.

Linux Kernel Configuration: Kernel configuration for a MSI 1039
Processor type and features --->
 Processor family --->
  AMD-Opteron/Athlon64
Bus options (PCI etc.)  --->
 [*] PCI Express support
Device Drivers  --->
 Block devices  --->
  <*> Packet writing on CD/DVD media
 ATA/ATAPI/MFM/RLL support  --->
  <*> ATA/ATAPI/MFM/RLL support
   <*>   Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
    <*>     Include IDE/ATA-2 DISK support
    <*>     Include IDE/ATAPI CDROM support
    <*>     generic/default IDE chipset support
    [*]     PCI IDE chipset support
     <*>       Generic PCI IDE Chipset Support
     [*]       Generic PCI bus-master DMA support
      [*]         Use PCI DMA by default when available
     < >         AMD and nVidia IDE support
     <*>         ATI IXP chipset IDE support
 IEEE 1394 (FireWire) support  --->
  <*> IEEE 1394 (FireWire) support
 Network device support  --->
  [*] Network device support
   Ethernet (1000 Mbit)  --->
    < > Realtek 8169 gigabit ethernet support
   Wireless LAN (non-hamradio)  --->
    [*] Wireless LAN drivers (non-hamradio) & Wireless Extensions
 Input device support  --->
  [*]   Mouse  --->
   <*>   PS/2 mouse
 Character devices  --->
  <*> /dev/agpgart (AGP Support)
   <*>   AMD Opteron/Athlon64 on-CPU GART support
 Graphics support  --->
  < > Support for frame buffer devices
 Sound  --->
  <*> Sound card support
 USB support  --->
  <*> Support for Host-side USB
   <*>   EHCI HCD (USB 2.0) support
   <*>   OHCI HCD support

Network Card

Read RTL8168 for details on how to install the driver for the network card. The most important thing is to wait until after rebooting before installing the driver. For some unknown reason, the driver will not work if it was installed in a chrooted environment created using the LiveCD. If you do install it before, it is almost impossible to make it work. It is easier to reformat the partitions used by Gentoo and restart the installation from scratch.

Backup Now

Due to the difficulty of installing, it would be wise to make a complete backup after rebooting and checking to see if the network card works correctly. That way, if a reinstall is necessary, the previous troubles wouldn't have to be dealt with again.

Video Card

The video card (ATI X1600) works correctly. However, the ebuild installed by emerge ati-drivers doesn't work. The driver must be obtained from ATI directly at http://www.ati.com/online/customercareportal/linux.html . It is installed by ./ati-driver-installer-(version).run and creating a file in /etc/env.d/ named something along the lines of /etc/env.d/00ati to add paths to $LDPATH for the libraries to be found correctly.

Code: /etc/env.d/00ati
LDPATH="/usr/lib64/fglrx:/usr/lib64/dri:/usr/lib64/xorg/modules/linux:/usr/lib64"

/etc/modules.autoload.d/kernel-2.6 must be edited so the fglrx module is loaded on startup

Code: /etc/modules.autoload/kernel-2.6
fglrx

/etc/X11/xorg.conf will still need to be configured.

CD and DVD Writing

When writing DVDs, the DVD writer can't write in TAO (Track At Once) mode. SAO or some other method must be used. This is an issue because the CD writing program cdrecord and its derivatives (i.e. k3b) default to TAO. This must be overridden. This is done by cdrecord -sao or some other option. Other CD writing applications will probably require a similar override.

Sound

The sound card is simple to configure with alsaconf. It should be hda-intel ATI Technologies Inc SB450 HDA Audio (rev 01). Note, KDE's Control Center can't test it and/or can't work with it even though the sound does work. The microphone does recieve sound but it is unknown whether it hears sound well.

Wireless Card

The wireless card is supported and the driver is installed by emerge rt2500. The interface for the wireless card is ra0.

Bluetooth

The USB Bluetooth can be detected by the kernel but it is unknown if it works nor how to configure it.

Builtin Camera

The builtin USB Camera can be detected by the kernel but it is unknown if it works nor how to configure it.

Multimedia Keys

The two contrast buttons, the USB camera button, and the wireless/bluetooth buttons work correctly with no configuration. The other multimedia buttons such as the volume buttons don't work by default. They may work but they are untested.

Appendix

lspci

The following is the output of lspci.

00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port
00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80)
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80)
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 82)
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (rev 80)
00:14.2 Audio device: ATI Technologies Inc SB450 HDA Audio (rev 01)
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: ATI Technologies Inc M56P [Radeon Mobility X1600]
04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
05:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21)
05:04.2 Class 0805: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01)
05:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
05:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02)
05:09.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)

dmesg

The following is the output of /var/log/dmesg

e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
 BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 MSI                                   ) @ 0x00000000000f9700
ACPI: RSDT (v001 MSI    1039     0x04192006 MSFT 0x00000097) @ 0x000000003ffd0000
ACPI: FADT (v002 MSI    1039     0x04192006 MSFT 0x00000097) @ 0x000000003ffd0200
ACPI: MADT (v001 MSI    1039     0x04192006 MSFT 0x00000097) @ 0x000000003ffd0390
ACPI: MCFG (v001 MSI    1039     0x04192006 MSFT 0x00000097) @ 0x000000003ffd03f0
ACPI: SSDT (v001    ATI ATIPATCH 0x00000001 INTL 0x02002026) @ 0x000000003ffd3eb0
ACPI: OEMB (v001 MSI    1039     0x04192006 MSFT 0x00000097) @ 0x000000003ffde040
ACPI: DSDT (v001    MSI     1039 0x04192006 INTL 0x02002026) @ 0x0000000000000000
On node 0 totalpages: 256990
  DMA zone: 2517 pages, LIFO batch:0
  DMA32 zone: 254473 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bff80000)
Built 1 zonelists
Kernel command line: root=/dev/hda5
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 3.579545 MHz PM timer.
time.c: Detected 2188.871 MHz processor.
time.c: Using PIT/TSC based timekeeping.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 1026104k/1048384k available (3658k kernel code, 21732k reserved, 1381k data, 208k init)
Calibrating delay using timer specific routine.. 4386.33 BogoMIPS (lpj=8772671)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
mtrr: v2.0 (20020519)
CPU: AMD Turion(tm) 64 Mobile Technology MT-40 stepping 02
Using local APIC timer interrupts.
Detected 12.436 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
PCI: Using MMCONFIG at e0000000
ACPI: Subsystem revision 20050902
GSI 21 sharing vector 0xA9 and IRQ 21
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
ACPI: Embedded Controller [EC] (gpe 6)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
PCI: Bridge: 0000:00:02.0
  IO window: 8000-8fff
  MEM window: fd800000-fd8fffff
  PREFETCH window: bbf00000-dbefffff
PCI: Bridge: 0000:00:04.0
  IO window: 9000-9fff
  MEM window: fd900000-fe0fffff
  PREFETCH window: dbf00000-ddefffff
PCI: Bridge: 0000:00:05.0
  IO window: a000-afff
  MEM window: fe100000-fe1fffff
  PREFETCH window: disabled.
PCI: Bus 6, cardbus bridge: 0000:05:04.0
  IO window: 0000b000-0000b0ff
  IO window: 0000b400-0000b4ff
  PREFETCH window: 52000000-53ffffff
  MEM window: 54000000-55ffffff
PCI: Bridge: 0000:00:14.4
  IO window: b000-bfff
  MEM window: fe200000-feafffff
  PREFETCH window: ddf00000-dfefffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 19 (level, low) -> IRQ 16
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1160069813.460:1): initialized
Total HugeTLB memory allocated, 0
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.25 [Flags: R/W].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
PCI: Setting latency timer of device 0000:00:02.0 to 64
pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
pcie_portdrv_probe->Dev[5a36:1002] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie01]
PCI: Setting latency timer of device 0000:00:05.0 to 64
pcie_portdrv_probe->Dev[5a37:1002] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie01]
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (31 C)
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
mkiss: AX.25 Multikiss, Hans Albas PE1AYX
AX.25: 6pack driver, Revision: 0.3.0
YAM driver version 0.8 by F1OAT/F6FBB
AX.25: bpqether driver version 004
baycom_ser_fdx: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA
baycom_ser_fdx: version 0.10 compiled 20:44:53 Sep 21 2006
hdlcdrv: (C) 1996-2000 Thomas Sailer HB9JNX/AE4WA
hdlcdrv: version 0.8 compiled 20:44:54 Sep 21 2006
baycom_ser_hdx: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA
baycom_ser_hdx: version 0.10 compiled 20:44:54 Sep 21 2006
netconsole: not configured, aborting
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
ATIIXP: chipset revision 128
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HTS721080G9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 < hda5 hda6 hda7 >
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 16
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 16, io mem 0xfebfd000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfebff000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 16, io mem 0xfebfe000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.3
usb 2-1: new low speed USB device using ohci_hcd and address 2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
input: Microsoft Microsoft USB Wireless Mouse as /class/input/input0
input: USB HID v1.11 Mouse [Microsoft Microsoft USB Wireless Mouse] on usb-0000:00:13.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: generic_sse
   generic_sse:  6694.000 MB/sec
raid5: using function: generic_sse (6694.000 MB/sec)
raid6: int64x1   2037 MB/s
raid6: int64x2   2925 MB/s
raid6: int64x4   2906 MB/s
raid6: int64x8   1954 MB/s
raid6: sse2x1    1054 MB/s
raid6: sse2x2    1679 MB/s
raid6: sse2x4    2349 MB/s
raid6: using algorithm sse2x4 (2349 MB/s)
md: raid6 personality registered as nr 8
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
oprofile: using NMI interrupt.
Netfilter messages via NETLINK v0.30.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 312 bytes per conntrack
ctnetlink v0.90: registering with nfnetlink.
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
ClusterIP Version 0.8 loaded successfully
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 6
G4KLX NET/ROM for Linux. Version 0.7 for AX25.037 Linux 2.4
NET: Registered protocol family 11
F6FBB/G4KLX ROSE for Linux. Version 0.62 for AX25.037 Linux 2.4
NET: Registered protocol family 3
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8:    0 : fid 0xe (2200 MHz), vid 0xa (1300 mV)
powernow-k8:    1 : fid 0xc (2000 MHz), vid 0xc (1250 mV)
powernow-k8:    2 : fid 0xa (1800 MHz), vid 0xe (1200 mV)
powernow-k8:    3 : fid 0x8 (1600 MHz), vid 0x10 (1150 mV)
powernow-k8:    4 : fid 0x0 (800 MHz), vid 0x16 (1000 mV)
cpu_init done, current fid 0xe, vid 0xa
ACPI wakeup devices: 
PCE4 PCE5 SBAZ P0P5 CBC0 USB1 USB2 EUSB 
ACPI: (supports S0 S1 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard as /class/input/input1
logips2pp: Detected unknown logitech mouse model 99
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
logips2pp: Detected unknown logitech mouse model 99
input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:04:00.0 to 64
eth0: Identified chip type is 'RTL8168B/8111B'.
eth0: r10001.02, the Linux device driver for Realtek Ethernet Controllers at 0xa800, 00:16:17:4e:40:05, IRQ 18
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
Realtek RTL8168/8111 Family PCI-E Gigabit Ethernet Network Adapter
Driver version:1.02
Released date:2006/02/23
Link Status:Linked
Link Speed:100Mbps
Duplex mode:Full-Duplex
I/O Base:0xA800(I/O port)
IRQ:18
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 920 MBytes.
[fglrx] module loaded - fglrx 8.28.8 [Aug 17 2006] on minor 0
ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 16 (level, low) -> IRQ 17
rt2500 1.1.0 BETA4 2006/06/18 http://rt2x00.serialmonkey.com
usbcore: registered new driver tiglusb
/root/tiglusb-1.07/tiglusb.c: TI-GRAPH LINK USB (aka SilverLink) driver, version 1.07
Adding 3494096k swap on /dev/hda7.  Priority:-1 extents:1 across:3494096k

Links

Retrieved from "http://www.gentoo-wiki.info/MSI_Megabook_m655"

Last modified: Thu, 28 Aug 2008 21:21:00 +0000 Hits: 8,549